සම්මන්ත්රණ සිංහයා
කුටිය: #E128
සැප් 17 – 18
අපි ඔබව මිටිවෝ කුටියේ හමුවීමට බලාපොරොත්තු වෙමු! තවත් හදාරන්න
IOT තාක්ෂණික එක්ස්පෝ යුරෝපය 2025
කුටිය: #202
සැප් 24 – 25

නිතර අසන ප්රශ්න

  • General Questions

  • බ්ලූටූත් බීකන්

  • වත්කම් ටැගය

  • IoT ගේට්වේ

  • පුද්ගල ටැගය

  • පුනරාවර්තකය

  • සංවේදකය

  • question
  • What environment is recommended for testing an AoA locator and beacon, and for parsing IQ values?

    For best results, keep the beacon within a 90-degree tilt angle of the locator and maintain at least one meter of distance between them to ensure more accurate phase difference readings.
  • What should we keep in mind when installing Bluetooth beacons or sensors in a factory, ගබඩාව, or office building?

    The most important rule is avoid direct contact with metal surfaces. Metal absorbs and reflects Bluetooth (2.4GHz) සං als ා, which can reduce signal strength by 50% or more—leading to poor coverage, lower positioning accuracy, or even failure to connect with gateways. For best performance, mount devices on non-metallic surfaces such as concrete walls, drywall, wood, or plastic.
  • Does Minew’s APP SDK support Go programming language development?

    Our SDK provides APIs only. If you plan to develop using Go, you will need to create a custom plugin bridge independently. Compatibility and success depend on your implementation and testing.
  • Can BLE beacons be modified by unauthorized third parties to alter broadcast content or operational behavior?

    බ්ලැක් විකාශන මූලධර්ම මත පදනම්ව, broadcast frames can be scanned and retrieved by third parties. කෙසේ වෙතත්, our devices are protected against direct unauthorized attacks. This is achieved through firmware-level encryption for configuration operations: without the required link key, the firmware will not respond to configuration commands, preventing third parties from modifying device settings. අතිරේක වශයෙන්, upon customer request, our devices can operate in a non-connectable mode to reject all connection attempts, further enhancing operational stability and security.
  • Can unauthorized third parties access BLE beacon broadcast data? Does this compromise data security?

    BLE broadcast data is inherently public and can be scanned by any device. While third parties may capture the payload (raw data), they cannot interpret its meaning without the specific frame parsing protocol.
  • Can Minew’s Beacons support custom firmware to connect with different customer gateways?

    ඔව්, we can customize the firmware. You need to provide the connection protocol for your gateway, and we will develop the necessary adaptation.
  • When configuring devices with the BeaconSET plus APP, why can’t some Minew devices be connected?

    The BeaconSET plus App scans and displays broadcast signals that meet Minew standards. Devices with different firmware versions might appear, but the App may not support connecting to all versions. Please refer to the device's user manual to ensure you are using the correct App or method for connection and configuration.
  • Can BLE be developed to implement a direction-finding positioning solution similar to UWB?

    If UWB isn't suitable for your project due to cost or other limitations, but you still need similar capabilities, you can use BLE in a few ways: BLE 5.1 with AoA or AoD technology, RSSI measurements with beacons, or BLE combined with IMU sensors.
  • Why did the batch import of MBT02 devices fail on the TagCloud 3.0 වේදිකාව?

    Please provide the failed import file, deviceImportResult.xlsx. We will analyze the content to determine the cause of the import failure. The error message at the end of the file will help us in our analysis.
  • Why can’t Apple devices select OTA packages in the app?

    iOS devices have permission issues that prevent the app from accessing documents outside the root directory. You can use third-party software to place the OTA package, certificates, and other necessary files in the app directory to make them accessible.
  • How long is your expected delivery?

    Minew has a global customer base and we ship to most countries around the globe. The actual delivery time is subjective to the client's location. We offer several shipment methods to meet your time constraints.
  • How does Minew ensure its quality control?

    Minew's product assurance is guaranteed by our premium services: our self-owned R&ඩී කණ්ඩායම, තත්ත්ව ඉංජිනේරු විද්යාව, factory production, සහ ආදිය. Minew's resources and control over every corner of the supply chain ensure only the best quality products will be shipped to our clients. Check https://www.minew.com/our-serivces/
  • Do you have an interface for connecting devices and data transmitted by Minew’s beacons?

    Minew provides an app and app development document for viewing product broadcast data and configuring products.
  • Can the E7 remove the battery and support an external power supply?

    Simply solder your own wires and replace the battery with an external power source, or let us customize it for you if you need to ship in bulk.
  • What’s the best way to install a beacon to have the strongest signal and broadcasting range?

    If the installation height is less than 2 මීටර්, the orientation of the three directions doesn't matter much. If the installation height exceeds three meters, the antenna should be placed in the downward position to have stronger signals.
  • MBM01 Ultra-Long Range Beacon සඳහා යෝජිත යෙදවීමේ ක්‍රම මොනවාද??

    බීකන් එකේ සංඥා විකාශන තරංග ආකෘතිය හෘද හැඩැති ය, එනම් ඇන්ටෙනාව දෙපස ශක්තිය ප්‍රශස්ත වේ. ඒ නිසා, ඇන්ටනාව පළමුව තබා හොඳම සංඥාව සඳහා අන්තරාලයේ පැති ස්ථානගත කරන්න. සටහන: ප්‍රදර්ශනාගාරයක බීකන්ස් කිහිපයක් තිබේ නම්, ඔයාට පුළුවන්: 1. විකාශන ශක්තිය සකස් කර දුර කෙටි කරන්න. 2. RSSI භාවිතයෙන් සංඥා ශක්තිය පෙරහන් කරන්න.
  • How can the P1 beacon be turned on and off without buttons?

    The P1 beacon can only be turned on via magnetic control and turned off through the app.
  • මට MTB02 කඩදාසි-බැටරි වත්කම් ටැගයට ACC සංවේදකය එක් කළ හැකිද??

    ඔව්, දිගු කරන ලද ප්ලග්-ඉන් සඳහා ඉඩ වෙන් කිරීමක් ඇත.
  • What is the impact on battery life if some tags remain off for 6 months before being turned on?

    According to product tests, the average energy consumption is very low when not turned on. Storing the product for 6 months under suitable conditions has no significant effect on its lifespan.
  • Can Minew’s asset tags identify whether the asset is stacked?

    If it is only necessary to determine whether the assets are stacked or not, a video/image sensor can be useful.
  • MTB02 කඩදාසි-බැටරි වත්කම් ටැගයේ මෙහෙයුම් වෝල්ටීයතා පරාසය කුමක්ද? විකාශනය නොකරන විට අවම වෝල්ටීයතාවය ගැන කුමක් කිව හැකිද??

    බැටරි වෝල්ටීයතාවය 1.2V හෝ 1200mV ට වඩා අඩු වූ විට MTB02 ක්‍රියා විරහිත වේ..
  • Can a European customer use the Plughub 1 (US standard) for testing?

    Long-term use is not possible, as it is a US-spec device with 125V/60Hz input only, a non-EU plug, and ETL certification (not valid for EU compliance). For short-term testing, it can be powered via an EU adapter, but the customer should monitor the device and ensure electrical safety.
  • Can the MG6 connect to both Ethernet and Wi-Fi, and automatically switch between them if one is disconnected?

    ඔව්. The MG6 supports multi-network failover. Once Ethernet, Wifi, and 4G are configured, it will automatically switch in the order Ethernet → Wi-Fi → LTE if a network fails.
  • What is the G1 gateway’s scanning accuracy, and how many tags can it handle? උදාහරණ වශයෙන්, can it accurately scan and upload 1,000 tags in a room within 5–10 minutes?

    The G1’s scanning performance depends on the tags’ broadcast power and interval—higher settings improve detection but increase power use. In good conditions, all tags can be scanned. With many BLE tags, channel congestion may cause random packet loss, which can be mitigated by adjusting channels, intervals, and filters.
  • For the G1-E gateway, if both Ethernet and Wi-Fi are available, which network is used by default? Can it automatically switch between them to maintain connection?

    The G1-E gateway does not support using Ethernet and Wi-Fi simultaneously. Only one can be active at a time. කෙසේ වෙතත්, when using Wi-Fi, it supports failover between different Wi-Fi networks if their passwords are preconfigured.
  • Could the AP block router’s Wi-Fi from connecting to the cloud?

    නැත. The AP doesn’t affect the router’s network. The issue is likely due to IP conflicts or unstable connections. Check for IP conflicts in the gateway, router, and upstream network, and set the gateway to DHCP mode. You can also try another Wi-Fi or use a wired connection.
  • Why does the G1-E give error code 671 when trying to get historical temperature data from an MST03 device?

    Error code 671 means the gateway can’t connect to the device. This can happen for several reasons:
    (1) The MST03 is too far from the G1-E, so the connection fails.
    (2) The MST03 has too much historical temperature data stored, which can cause it to disconnect when the gateway tries to retrieve the data.
    (3)The command sent over MQTT has an incorrect password or the wrong MAC address.
  • Does the MG6 gateway support the AMQP protocol?

    නැත, it doesn’t.
  • What is the maximum supported SD card capacity for the MG6 gateway?

    It is recommended to use SD cards no larger than 32GB. Cards above this size may have stability issues over the SPI interface, leading to detection failures or frequent I/O errors.
  • Does the MG6 gateway send acknowledgment packets to confirm connection and data transmission?

    It depends on the communication protocol: MQTT: Acknowledgments are handled by the MQTT protocol itself, based on the selected QoS level. HTTP: The gateway expects a 200 status code from the server in response to every HTTP POST request, regardless of whether the uploaded data is empty. Tcp: As a transport-layer protocol, TCP does not include application-level acknowledgments. The server must handle packet reassembly manually.
  • බහු Mg3 / mg4 උපාංග එකම බලැති USB හබ් ෆ්ලෑෂ් රතු සහ හරිත විකල්පයක් ලෙස සම්බන්ධ කරන්නේ ඇයි?, සාර්ථක ජාල සහ සේවාදායක සම්බන්ධතාවයෙන් පසුව පවා?

    මෙය ප්රමාණවත් නොවන බල සැපයුම නිසා ඇතිවේ. එක් USB කේන්ද්රස්ථානයක් පමණක් බල කිරීම සඳහා අපි නිර්දේශ කරමු එක් mg3 හෝ mg4 උපාංගයක් පමණි.
  • Can the MG6 gateway send downlink commands to BLE devices from other manufacturers?

    දැනට, it only supports downlink control for Minew BLE devices using our proprietary protocol. කෙසේ වෙතත්, we have developed a new MG6 firmware that supports standard BLE protocols, which will be released soon.
  • Does the MG3 gateway support communication via SOCKS proxy?

    The MG3 does not support SOCKS proxy communication.
  • වින්යාස කරන ලද ස්ථානගත කිරීමේ පරතරය අනුව MWC03 ලාංඡන ලාංඡනය GNS දත්ත නොපැමිණෙන්නේ ඇයි??

    GNSS පරතරය යනු උපාංගය GNS මොඩියුලයෙන් දත්ත ලබා ගන්නේ කෙසේද යන්න පමණක් අර්ථ දක්වයි. නැවත ලබාගත් GNSS දත්ත ඊළඟ LTE වාර්තා චක්රය තුළ උඩුගත කරනු ලැබේ, වෙනම වාර්තා කිරීමේ කාලසටහනක් මත නොවේ.
  • Can the C10 with 13.56MHz NFC be read by an iPad’s NFC reader?

    iPads do not natively support NFC reading. To use this function, an external third-party NFC reader is required.
  • MWC03 ස්මාර්ට් ලාංඡනය වේදිකා ඒකාබද්ධ කිරීම සඳහා SDKS / APIs පිරිනමයි?

    MWC03 SDKs හෝ APIs ලබා නොදෙන අතර, අපගේ නැනෝල්ක් ප්රොටෝකෝලය භාවිතයෙන් ගනුදෙනුකරුවන්ට බාධාවකින් තොරව සේවාදායක පැත්තේ ඒකාබද්ධතාවයක් ලබා ගත හැකිය.
  • The MWB01 tag is similar in size to the AirTag. Can it be used with AirTag cases?

    ඔව්, the MWB01 has the same size, so customers can use available AirTag cases. We can also assist with purchasing and shipping them if needed.
  • Can the wristband color be customized?

    ඔව්, custom wristband color is supported. දැනට, the available colors are black, සුදු, සහ අළු. For other colors, please provide the details for evaluation.
  • C10 කාඩ් බීකන් සහ MWC01 ලාංඡනය වැනි උදාසීන එන්එෆ්සී ටැග් සඳහා නිෂ්පාදන මැක් ලිපින හෝ අනුක්රමික අංක ලිවිය හැකිද??

    ඔව්, තොරතුරු දිග එන්එෆ්සී චිපයේ සීමාව ඉක්මවා නොයන තාක් කල්.
  • ජීපීඑස් සං als ා පමණක් වාර්තා කිරීම සඳහා බ්ලූටූත් ස්කෑන් කිරීම අක්රීය කිරීම MWC03 සහාය ලබා ගන්න, හෝ බ්ලූටූත් දත්ත පමණක් වාර්තා කිරීම සඳහා ජීපීඑස් අක්රීය කිරීම?

    ඔව්, එය මෙම වින්යාසයන් සඳහා සහය දක්වයි, දුරස්ථ වින්යාසය සඳහා ඔබේම වේදිකාවක් සමඟ ඒකාබද්ධ කළ හැකිය.
  • How does the MWB01 Dynamic Tag fulfill personnel management?

    MWB01 Dynamic Tag achieves personnel management and indoor positioning by leveraging built-in NFC function and Bluetooth LE tracking technology. අතිරෙකව, the MWB01 is portable, lightweight, and supports various wearable options.
  • What is the expected service lifespan of the MWC02 Ultra-thin Location Card?

    MWC02 Ultra-thin Location Card supports an above 2-year service life. To cope with various application scenarios, MWC02 is also upgraded with IP67 waterproof ability.
  • සී 10 කාඩ් බීකන් හි ඇස්තමේන්තුගත විකාශන පරාසය කුමක්ද??

    C10 කාඩ් බීකන් බ්ලූටූත්ට සහාය වේ 5.0 සහ මීටර 100 ක විකාශන සම්ප්රේෂණ පරාසයක්, ගෘහස්ථ සැකසුම් වලට විශේෂයෙන් අදාළ වේ, රෝහල් සහ සේවා ස්ථාන වැනි.
  • How to enable the sleeping mode of B7 Button Wristband?

    After enabling "Trigger Settings" and completing the ACC setup, customers can turn off "Usual Broadcast". This will make the frame broadcast for a configurable period only when ACC is triggered and stop when not triggered. ඊට අමතරව, no firmware update is required.
  • MBT02 වත්කම් වත්කම් බ්ලූටූත් පුනරාවර්තනය වෙනස් කළ හැකි අතර එමඟින් ත්වරණය පමණක් ස්කෑන් කිරීම අවුලුවාලිය හැකිය?

    ඔව්, එය වෙනස් කළ හැකිය. වත්මන් MBT02 මණ්ඩලයට වෙන් කර ඇති ත්වරණ සංවේදකයක් ඇත; එයට ස්ථිරාංග අනුවර්තනය අවශ්ය වේ.
  • How is a LoRaWAN node’s power consumption managed?

    Nodes are battery-powered and designed for low power use. Sleep modes and optimized transmission intervals help extend battery life.
  • What is the typical maximum communication range between a LoRaWAN node and the network?

    It depends on factors like power, ඇඟිලි ගැසීම්, and terrain. Generally, a few kilometers in urban areas, but over 10 km in open rural environments.
  • What are the main ways to configure parameters?

    Via downlink commands. For Class A devices, new settings are received and applied when they next send data.
  • Can a single LoRa device connect to multiple network servers?

    නැත. Once registered, the device is bound to one server with a unique devaddr. Other servers can't receive its data unless it re-joins and registers with them.
  • How is the timing function in the S4 door sensor?

    The S4 device can only record its own runtime. Accurate timing requires network time synchronization. To improve timing accuracy, our device includes an internal clock crystal. Each time the device connects to the app or gateway to download historical data, it automatically synchronizes time, enhancing the reliability of timing-related operations.
  • යෙදවීමේදී 12V හි වෝල්ටීයතාවය ස්ථාවර කළ නොහැකි නම් MSR01 හි මෙහෙයුම් වෝල්ටීයතා පරාසය කුමක්ද??

    MSR01 10V-25V හි මෙහෙයුම් වෝල්ටීයතා පරාසයකට සහාය වේ.
  • MSR01 මිලිමීටර තරංග රේඩාර් රේඩාර් සංවේදකය සෘජු ප්රතිදානය RAW රේඩාර් හඳුනාගැනීමේ දත්ත?

    අපගේ MSR01 දැනට අමු රේඩාර් පරිලෝකනය කිරීමේ දත්ත තෙවන පාර්ශවීය පද්ධති වෙත සම්ප්රේෂණය කිරීමට සහාය නොදක්වයි. ඒ වෙනුවට, එය සම්බන්ධීකරණ දත්ත හා සංඛ්යාන ගණන් කිරීම වැනි සැකසූ ප්රති results ල ප්රතිදානය කරයි. ස්වාධීන විශ්ලේෂණය සඳහා මිලිමීටර-තරංග රේඩාර් සහිත රේඩර් රේඩාර් දත්ත වෙත ඔබට ප්රවේශය අවශ්ය නම්, ඔබගේ විශේෂිත ව්යාපෘති අවශ්යතා සමඟ පෙළගැස්වීම සඳහා අපට ස්ථිරාංග අභිරුචිකරණය කළ හැකිය.
  • MSR01 මිලිමීටර තරංග රේඩාර් සංවේදක සංවේදක සහාය නොදක්වන පුද්ගලයින්ගේ සමුච්චිත සංඛ්යාවක්?

    නැත, MSR01 දැනට වාර්තා කිරීම සඳහා වාර්තා කිරීම නියමිත කාල සීමාවන් තුළ අනාවරණය වූ පුද්ගලයින්ගේ සංඛ්යාව පමණි.
  • Does the S4 Bluetooth® 5.0 Door Sensor support broadcasting and alerting only when a state change occurs?

    ඔව්, it also supports periodic broadcasting, and the broadcasting interval can be configured.
  • පතල් වත්තකින් තොරව පරිගණකයක් මත msr01 දත්ත ලබා ගත හැකිද??

    Msr01 හි බ්ලූ අනුවාදය සඳහා, පළාත් සභාවකට බීකන් විකාශන දත්ත කෙලින්ම පරිලෝකනය කළ නොහැක. කෙසේ වෙතත්, බාහිර නෝර්ඩික් ඩීකේ මෙවලම භාවිතයෙන් හෝ NRF සම්බන්ධකයේ පළාත් සභා අනුවාදය බාගත කිරීමෙන් පරිලෝකනය කර ලැබිය හැකිය. MSR01 හි වයිෆයි අනුවාදය සඳහා, අතිරේක බිම් ගේට්වේ එකක් අවශ්ය නොවේ. MSR01 විසින් වාර්තා කරන ලද රේඩාර් අනාවරණය කිරීමේ දත්ත MQTTT.FX ග්රාහක මෘදුකාංගය හරහා පරිගණකයක් මත ලබා ගත හැකිය.
  • MSR01 හි රේඩාර් සං signal ාව මිනිස් සිරුරුන්ට කිසිදු හානියක් කරයි?

    රේඩාර් ආරක්ෂිත 60GHz සංඛ්යාතයකින් ක්රියාත්මක වේ, මිනිසුන්ට කිසිදු හානියක් නොකරයි. රේඩාර් පද්ධති, 60GHz හි ක්රියාත්මක වන අය ඇතුළුව, ස්ථාපිත මානව නිරාවරණ සීමාවන් තුළ ආරක්ෂාව සහතික කිරීම සඳහා නිර්මාණය කර ඇත.
  • MSR01 මිලිමීටර තරංග රේඩාර් සංවේදකය මිනිසුන් හෝ වස්තූන් හඳුනා ගැනීම සඳහා පිළිතුරු දෙන්නේ කුමක්ද??

    එය මානව හඳුනාගැනීමේ ලක්ෂණ භාවිතා කරයි, සතුන් සතුන් වෙත ද ව්යාප්ත විය හැකිය, නමුත් ලෝහයෙන් රේඩාර් මැදිහත්වීම සමඟ. උස හඳුනාගැනීමේ සැකසුම් මිනිස් ගමනාගමනය ඇති විට එවැනි මැදිහත්වීම් පෙරහන් කළ හැකිය. අමතර ලේබල් නොමැතිව වස්තූන් හඳුනාගත හැකිය, ඇල්ගොරිතම මිනිසුන් සහ වෙනත් වස්තූන් අතර ස්වයංක්රීයව වෙන් කරයි.
සජීවී කතාබස්

නිෂ්පාදනය ඔබේ ව්‍යාපාරයට සුදුසු එකක් දැයි කල්පනා කිරීම? සැබෑ මිනිසුන් සමඟ කතාබස් කරන්න.

දැන් කතාබස් කරන්න දැන් කතාබස් කරන්න ඊමේල් කරන්න
ඔයාට ස්තූතියි අපගේ කණ්ඩායම ඔබට විද්‍යුත් තැපෑලෙන් පිළිතුරු දෙනු ඇත 24 පැය. ඔබට එය නොලැබුණහොත්, කරුණාකර ඔබගේ කුණු තැපැල් පෙට්ටිය පරීක්ෂා කරන්න.